Volkswagen jetta oil filter location

Volkswagen jetta oil filter location DEFAULT

2011-2018 VW Jetta Oil & Filter Replacement

  • Ensure car jack is ready by rotating handle clockwise completelyLocate metal beam under car used for jackingPosition car jack platform under metal beam
    • Ensure car jack is ready by rotating handle clockwise completely

    • Locate metal beam under car used for jacking

    • Position car jack platform under metal beam

    Edit

  • Lower car onto the stands by rotating the jack handle counter-clockwise (very gently)Depending on your model of jack, the jack may lower rapidly or slowly. Do your best to lower the car gentlyRepeat steps 1-3 on driver side of car
    • Lower car onto the stands by rotating the jack handle counter-clockwise (very gently)

    • Depending on your model of jack, the jack may lower rapidly or slowly. Do your best to lower the car gently

    • Repeat steps 1-3 on driver side of car

    • At this point, both sides should be raised off the ground

    • Place clean cardboard underneath the car

    Edit

  • Locate the oil container underneath the car (this will require crawling under the car and laying on your backLocate the bolt used to drain the oilPosition the oil drip pan underneath the bolt
    • Locate the oil container underneath the car (this will require crawling under the car and laying on your back

    • Locate the bolt used to drain the oil

    • Position the oil drip pan underneath the bolt

    Edit

  • Loosen the bolt by turning the 5/16 allen wrench counter-clockwiseIt may take a significant amount of force to loosen the boltOnce loose, remove the bolt by hand
    • Loosen the bolt by turning the 5/16 allen wrench counter-clockwise

    • It may take a significant amount of force to loosen the bolt

    • Once loose, remove the bolt by hand

    • Once the bolt is removed, oil will immediately flow out

    • Make sure the oil drip pan is positioned well

    • Once the bolt is removed, you will get a significant amount of oil on your hand

    • Don't drop the bolt into the oil pan. It will be slippery!

    • Wait ~10 minutes for all the oil to drain out

    Edit

  • Clean up the drainage hole with paper towelYou may need to use a paper towel to wipe up any beading oilInsert the bolt, turning clockwise
    • Clean up the drainage hole with paper towel

    • You may need to use a paper towel to wipe up any beading oil

    • Insert the bolt, turning clockwise

    • Tighten the bolt with the 5/16 allen wrench until the wrench won't turn any further. This is plenty tight.

    Edit

  • Position drip pan underneath the plastic cover as shown in pictureOpen the hood of the carLocate the oil filter
    • Position drip pan underneath the plastic cover as shown in picture

    • Open the hood of the car

    • Locate the oil filter

    • The oil filter is near the front of the car

    • The oil filter looks like a cylinder

    Edit

    • Loosen the oil filter by hand

    • It may take a significant amount of force to loosen the oil filer

    • A filter wrench can be used to help loosen the filter

    • Turn the filter clockwise to loosen (from the perspective of the user) - see video if you're confused

    • Remove oil filter

    • Once you remove the filter, some remaining oil will spill out, onto your hand, and into your well placed oil drip pan

    • The filter may be very slippery, don't drop it!

    Edit

    • Get new oil filter

    • Install oil filter

    • Turn the oil filter counter clockwise to install (as appears to the user)

    • Tighten by hand until both hands can't get it any tighter - This is plenty tight

    Edit

  • Sours: https://www.ifixit.com/Guide/2011+2012+2013+2014+2015+2016+2017+2018+VW+Jetta+Oil+&+Filter+Replacement/117266

    How to Change the Oil Filter in a 2008 Jetta

    The oil filter on the 2008 Volkswagen Jetta is the most important component of the oil cleaning process. The oil enters the oil filter from the oil pan. The sediments are trapped inside of the oil filter before the oil reaches the engine. Over a period of time, the oil filter will become clogged with sediments and will need to be replaced. Volkswagen recommends replacing the oil and filter on the Jetta every 3,000 miles.

    Step 1

    Park the 2008 Volkswagen Jetta on a level surface and shut off the engine. Open the hood and unscrew the oil cap from the engine. The oil cap is located on the top driver side of the engine.

    Step 2

    Jack up the Jetta and place the jack stands behind each front tire on the frame rail of the car. Lower the car onto the jack stands. Make sure that the car is securely on the jack stands.

    Step 3

    Crawl under the front of the car and remove the plastic shield that is covering the bottom of the engine. There are four standard plastic Torx bolts that are connecting the plastic shield to the frame. Remove the Torx bolts with a 3/8 ratchet and a standard Torx bit.

    Step 4

    Locate the oil filter underneath the car. It is inside of the oil filter housing that is located on the driver side of the engine block above the oil pan. Slide the oil catch pan underneath the oil pan.

    Step 5

    Push the small knob on the bottom of the oil filter housing to drain the oil from the filter. Let the oil drain into the oil catch pan until the filter is empty.

    Step 6

    Slide the 76 mm oil filter cup tool onto the 3/8 inch drive socket. Then slide the oil filter cup tool onto the bottom of the oil filter housing. Turn the oil filter housing counterclockwise to loosen the oil filter. Once the oil filter is loose, finish removing it with your hands.

    Step 7

    Pour any excess oil from the oil filter housing into the oil catch pan. Remove the O-ring from around the oil filter threads and replace it with the new O-ring that comes with the new oil filter.

    Step 8

    Slide the old oil filter cartridge out of the oil filter housing and replace it with the new one.

    Step 9

    Screw the oil filter housing back onto the oil filter housing base on the engine block. Tighten the oil filter housing with the 3/8-inch drive ratchet and the 76 mm oil filter cup tool. Turn the oil filter housing clockwise to tighten.

    Slide the oil catch pan out from under the car. Jack up the car and remove the jack stands.

    References

    Tips

    • The oil filter cartridge part number for the 2008 Volkswagen Jetta is K&N oil filter-HP-7010

    Things You'll Need

    • Jack
    • Jack stands
    • 3/8 inch drive ratchet
    • Standard Torx bit
    • Oil catch pan
    • 76 mm oil filter cup tool
    • New oil filter

    Warnings

    • Always wear safety glasses when working around oil.

    Writer Bio

    Grace Mclain has been writing professionally since 1998. Her articles have appeared on eHow.com, Answerbag.com and LIVESTRONG.COM, and she specializes in automotive and business topics. McIain has a professional writing certificate from JB Hunt in Little Rock, Ark.

    More Articles

    Sours: https://itstillruns.com/change-oil-filter-2008-jetta-6223571.html
    1. On its own synonym
    2. Outlook 2007 multiple exchange accounts
    3. Wiring mr cool mini split
    4. Tree of savior classes
    5. 2019 f350 diesel for sale

    A Volkswagen oil change must keep your engine in good condition and avoid engine overheating and, thus, failure.

    Auto Repairs Are EXPENSIVE


    That been said, it is important to understand the required tools and steps needed for your Volkswagen’s oil change. Furthermore, you need to understand the type and required amount of oil needed to be added to avoid overfilling or getting in situations where you have low engine oil. 

    In this article, we provide you with a detailed step by step guidance on how to change your Volkswagen’s oil and how to reset the oil change check light, in case you had it turned on. Lastly, we provide information on how much it will cost you to change your Volkswagen’s oil at home or a professional repair shop.

    Volkswagen Oil Change

     

    This section provides you with a list of the main tools you need to prepare before even starting the oil change process. Then, we walk you through what needs to be done to change the oil and reset the oil change check light.  

     

    • Prepare the required tools 

     

     

    To change your Volkswagen’s oil, you need the following parts and tools; some of these tools are specific for a Volkswagen, and others are just general tools you need to have for any oil change despite the vehicle type.

    • Volkswagen required oil change parts
      • A filter
      • The appropriate type of oil needed for a Volkswagen
      • A drain plug washer
    • General oil change parts
      • Your vehicle’s owner’s manual. You will need to refer to the manual a couple of times as you change your Volkswagen’s oil. Thus, it is recommended to have a manual copy handy while you’re working. If you don’t have a copy of the manual, you can either download it from the web or request a hard copy from your local mechanic
      • A funnel to pour the oil
      • A pan to drain the old oil and prevent oil from splashing on the floor
      • A ½ inch 36mm socket
      • A 6-inch extension and ratchet
      • A 19 mm wrench 
      • A ¼ inch socket screwdriver that has a T-25 Torx Bit

     

    • Volkswagen oil change steps

     

     

    To change your Volkswagen’s oil, you need to prepare the vehicle, drain the old oil, install a new filter and drain plug washer, add the required amount of engine oil, and reset the change oil check light.

    • Before starting any step in the actual oil change, you need to prepare your vehicle, including:
      • Please park your vehicle in a location where it is easy to work. Usually, an open area or your garage would be ideal
      • Run the engine for about five to ten minutes to warm it up. This way, your engine’s oil gets heated up a little, and it drains out of the drain plug easier.
      • Locate your vehicle’s under-body splash pan by referring to the vehicle’s owner’s manual. 
      • Remove the under-body splash pan by unscrewing the T-25 screws using the ¼ inch socket screwdriver.
      • Once the under-body splash pan is removed, place a big enough container to collect your old engine oil under the oil drain plug. 
      • Minimize the crankcase pressure by loosening up the oil fill cap to help easier oil flow out of the drain plug
      • Remove the oil drain plug using the 19mm wrench and let the oil drain completely inside the container.
      • Inspect the oil drain plug. The oil drain plug must be in good condition to prevent oil leaks. Inspect the oil drain plug by looking for any signs of the worn or crushed washer. It is important to note that a worn drain plug can damage the entire oil pan threads resulting in higher repair costs. 
      • After the oil finishes draining, it is recommended to clean excessive old oil 
      • Install the new drain plug, or the old one if it is in good condition
      • Move your oil container to a location under the oil filter in preparation for replacing the oil filter. 

     

    • Install the oil filter and replace the O-ring
      • Before starting with the process, you need to refer to the vehicle’s manual and locate the oil filter's correct location.
      • Once you know where the oil filter is located, make sure the oil container is placed in the right position to collect any oil splashes from getting to the floor
      • Remove the oil filter cap using the ½ inch 36mm socket and the 6-inch extension. 
      • It is important to note that the oil filter cartridge is made of plastic; therefore, you need to be a little gentle as you pull it out of the oil housing.
      • Allow the oil to drain out of the oil filter for about 30 seconds
      • It is good to compare the old oil filter to the new one to make sure you bought the right filter for our vehicle. You can also refer to the vehicle’s owner’s manual to confirm the type of filter needed.
      • Remove the filter and the old O-ring
      • Install the new filter along with the new O-ring
      • Before putting the filter cap back, it is recommended to add a little of the oil to the O-ring. This way, the O-ring doesn’t get bent inside the oil housing. 
      • When torquing the filter’s cap, you don’t need to tighten it too much to avoid breaking the oil filter housing in your next oil change, only about 17 ft-lb.
      • Now you are ready to pour the new oil
    • Add the required amount of oil to your oil filer
      • Locate the oil filter by referring to the vehicle’s owner’s manual
      • Remove the cap and put the filling funnel
      • Make sure not to overfill the engine’s oil filler. It would help if you had no more than 0.5 liters less than the vehicle’s full capacity
      • To make sure you put the right amount of oil, it is a good practice to monitor the oil level using the dipstick
      • Close the oil filter cap and start the car for about 30 seconds to warm up the engine and make sure the oil filter housing is filled as well
      • Watch for any signs of leaks from the oil filter housing or the oil drain plug
      • Turn the engine off and reinstall the under-body splash
      • Take a final look at your oil level after you put the vehicle on the ground level
    • You must dispose of the old oil to a certified recycling collection center.

     

    • Reset your Volkswagen oil change light

     

     

    Resetting your Volkswagen’s oil change light might differ depending on your Volkswagen’s model. The best way to confirm if the coming steps work for your Volkswagen is by referring to the vehicle’s owner’s manual.

    This section shows you how to reset the oil change light for the 2019 Volkswagen Jetta. 

    • Resetting change oil light for a 2019 Volkswagen Jetta with Digital Instrument Cluster
      • Turn on your vehicle’s ignition without starting the engine
      • On your steering wheel, press and hold the OK button for about four seconds while making sure the MFI is still in range
      • After the four seconds, release the OK button as you see the service menu popping up
      • Select “reset oil change” using the steering wheel’s control buttons
      • Finally, select “reset inspection,” then “OK” and confirm by pressing “OK” again
    • Resetting change oil light for a 2019 Volkswagen Jetta with a Conventional Instrument Cluster
      • Make sure the ignition switch is turned off
      • Locate the “0.0” button by referring to the vehicle’s owner’s manual. This button is usually under the instrument cluster.
      • Once you find it, press and hold 
      • While you are holding the “0.0” button, turn on the ignition switch without starting the engine
      • Select the appropriate message that serves your needs between the following messages:
        • “Reset oil change service.”
        • “Do you want to reset inspection?”
      • Press the 0.0 button to confirm your selection
      • Watch for a confirmation message 

    How much does it cost to perform a Volkswagen Oil Change?

     

    According to RepairPal.com, changing your Volkswagen’s oil costs you between $112 and $138 on both parts and labor costs. 

    If you decided to change your Volkswagen’s oil by yourself, you could drop these numbers to $76 and $92.

    While changing your Volkswagen’s oil can save you a lot of money, it is recommended that you don’t do it if you don’t have the required minimum mechanical skills. This is because most DIYs do not work the first time, and any mistakes in car repairs can cause significant damages that require a lot of money and effort to get fixed. 

    Conclusion

    The Volkswagen oil change is essential to prevent engine damage due to overheating. 

    To perform your Volkswagen oil change, you need to prepare the required tools, drain the old oil, install a new oil filter, add the required amount of oil, and reset the change oil light button.

     

    Categories BlogSours: https://www.cashcarsbuyer.com/volkswagen-oil-change/
    VW Jetta engine oil and filter change

    VW Jetta 2.5L I5 Engine Oil Change Guide
    How to change the 2.5L I5 engine oil and replace the filter in a 6th generation MK6 2011-2014 Volkswagen Jetta.

    VW-Jetta-I5-Engine-Oil-Change-Filter-Replacement-Guide-001
    2012 VW Jetta 2.5L I5
    VW-Jetta-I5-Engine-Oil-Change-Filter-Replacement-Guide-002
    Twist Off Oil Filler Cap
    VW-Jetta-I5-Engine-Oil-Change-Filter-Replacement-Guide-003
    Pull Up Oil Dipstick
    This automotive maintenance tutorial was specifically written to assist owners of the 6th generation MK6 (2011, 2012, 2013 & 2014) Volkswagen Jetta sedan or Jetta SportWagen in changing the engine oil and replacing the cartridge oil filter in the 2.5 liter inline five cylinder motor.

    Owners of other VW Group vehicles equipped with the 2.5L L5 engine such as the previous generation MK5 (2005-2010) Jetta, Vento, Bora, Passat, Lavida, Sportwagen, Rabbit, Beetle, Golf, Eurovan and Seat Toledo may also find these DIY instructions to be helpful.

    The items needed to complete this procedure include a floor jack, two jack stands, a Torx T25 star bit screwdriver, a 19mm socket, a 3/8" drive ratcheting wrench, a used oil catch container, a 74mm oil filter wrench with 14 flats (A.K.A. "flutes" or "points"), a new cartridge style oil filter and 7 U.S. quarts of new SAE 5W-40 synthetic oil.



     A few compatible oil filter wrenches that are approximately 74mm in size with 14 flats include the following with their part numbers: Assenmacher Specialty Tools # M 0219 (74mm), SmartDIY 903, Hazet # 2169 (74.4mm), AST Tools # 2175 (74.5mm) and the MetalNerd # MN7614 (74-76mm).

    To use the AST Tools # M0219 wrench, you'll need either a 3/8" drive ratcheting wrench to insert in to the hole on the top or attach a 22mm socket with a 1/2" drive ratcheting wrench to the hex head.

    Replacement aftermarket cartridge style oil filter elements with their part numbers are as follows: Mann-Filter HU 719/6 X, K&N PS-7010, Mobil 1 M1C-451, Bosch L3581, Wix 57187, Mahle OX 379D, Pennzoil HPZ-162, Ecogard X5581, Purolator L35581, ACDelco PF2257, Beck Arnley 041-8184, Angstrom Autohaus 06D115562 and Volkswagen 06D115562.

    VW-Jetta-I5-Engine-Oil-Change-Filter-Replacement-Guide-004
    Plastic Under Engine Cover
    VW-Jetta-I5-Engine-Oil-Change-Filter-Replacement-Guide-005
    Silver Drain Plug Bolt
    VW-Jetta-I5-Engine-Oil-Change-Filter-Replacement-Guide-006
    Remove Torx T25 Screws
    The first three steps are to warm up the engine for a few minutes, park the car on a level surface and then shut off the engine.

    Warming up the engine will help suspend any contaminants or "sludge" within the old oil and also allow it to drain out more quickly.

    Then engage the emergency / parking brake and chock the rear wheels to prevent the vehicle from moving.

    Open the hood, twist off the oil filler cap in the counter clockwise direction and pull up the yellow handled oil level dipstick a few inches.

    Removing the oil filler cap and pulling up the dipstick a few inches will help prevent a vacuum from forming and help the old oil drain out more quickly.

    Raise the front passenger side of the vehicle with the floor jack and securely support it with the two jack stands.

    I prefer to raise just the front passenger side of the car to access the underside of the engine and leave the three other wheels on the ground for extra safety.

    You may choose to raise the entire front of the vehicle or use ramps instead of stands.

    Slide under the front passenger side of the engine bay with a Torx T25 screwdriver, a 19mm socket, a 3/8" drive ratcheting wrench, the used oil catch container and a small flathead screwdriver.

    VW-Jetta-I5-Engine-Oil-Change-Filter-Replacement-Guide-007
    Four Screws On Each Side
    VW-Jetta-I5-Engine-Oil-Change-Filter-Replacement-Guide-008
    Pull Out Plastic Tab At Front
    VW-Jetta-I5-Engine-Oil-Change-Filter-Replacement-Guide-009
    Remove Other Four Screws
    The silver metal oil drain bolt is located at the rear edge of the black metal oil pan towards the back of the engine bay.

    To access the oil filter housing, you'll need to remove the 8 screws holding the black plastic under engine cover (A.K.A. "belly pan" or "splash guard") in place.

    Remove the screws by turning them counter clockwise with the Torx T25 star bit screwdriver.

    There are 4 screws on the passenger side and another 4 on the driver's side of the panel.

    Pull the cover towards the rear of the vehicle to separate the two tabs on the front edge from their slots.

    Set the plastic cover and the 8 screws aside in a safe place.

    VW-Jetta-I5-Engine-Oil-Change-Filter-Replacement-Guide-010
    Plastic Oil Filter Housing
    VW-Jetta-I5-Engine-Oil-Change-Filter-Replacement-Guide-011
    Position Used Oil Basin
    VW-Jetta-I5-Engine-Oil-Change-Filter-Replacement-Guide-012
    Loosen 19mm Drain Plug
    The round black plastic oil filter housing is located just in front of the black metal oil pan and it is surrounded by rubber hoses.

    Slide the used oil catch basin to just below the oil drain plug.

    Loosen the oil drain bolt by turning it counter clockwise with the 19mm socket and 3/8" drive ratcheting wrench.

    VW-Jetta-I5-Engine-Oil-Change-Filter-Replacement-Guide-013
    Drain Out Old Motor Oil
    VW-Jetta-I5-Engine-Oil-Change-Filter-Replacement-Guide-014
    Tighten 19mm Oil Drain Bolt
    VW-Jetta-I5-Engine-Oil-Change-Filter-Replacement-Guide-015
    Unscrew Plastic Cap
    Be careful when you remove the oil drain bolt, since the old oil may be hot enough to burn your skin depending on how long you warmed up the engine.

    I'd recommend wearing latex rubber or Nitrile gloves when removing the oil drain plug to keep your hands clean since used engine oil may contain carcinogenic chemicals and/or heavy metals that may cause skin cancer.

    Spin out the oil drain bolt and allow the old oil to drain out for at least a few minutes or until the flow slows to an occasional drip.

    Volkswagen recommends replacing the oil drain bolt at every oil change. Some people prefer to replace the drain plug every other oil change or every third oil change. The OEM part number for the new oil drain plug is # N90813202.

    Spin in the oil drain bolt by hand in the clockwise direction to prevent it from becoming cross threaded.

    Tighten the oil drain bolt with the 19mm socket and ratcheting wrench in the clockwise direction to just past hand tight or about 22 ft-lbs (30 Nm) of torque.

    Do not over tighten the oil drain bolt to prevent from stripping the aluminum threads.

    Double check that the drain plug is tight before moving on to the next steps.

    Next, unscrew the small plastic end cap at the bottom of the oil filter housing attached to a black tether cable in the counter clockwise direction.



     

    VW-Jetta-I5-Engine-Oil-Change-Filter-Replacement-Guide-016
    Push In Drain Nipple
    VW-Jetta-I5-Engine-Oil-Change-Filter-Replacement-Guide-017
    Attach 74mm Filter Wrench
    VW-Jetta-I5-Engine-Oil-Change-Filter-Replacement-Guide-018
    Spin Off Counter Clockwise
    Once the cover is removed, you'll see the the reddish orange drain nipple.

    Move the used oil catch basin to just below the oil filter housing.

    Gently push the drain nipple up at an angle with a small flathead screwdriver until it stays in place.

    Allow the old oil to drain out of the oil filter housing.

    Gently push up on the drain nipple again until it can be released back in to the down "closed" position.

    If you are concerned about damaging the drain nipple with out using the special VW / Audi "Oil Filter Housing Drain Tool" (part # T40057 from AST Tools), you can just skip the preceding steps.

    To avoid having to pay anywhere from $60 to $80 for the specialty drain tool, you can either use a screwdriver to push in the drain nipple or just twist off the filter housing and wear gloves to keep the old oil off your hands.

    Attach the 74mm with 14 flats oil filter wrench to the black plastic oil filter housing.

    Loosen the filter housing by rotating it in the counter clockwise direction using the appropriate socket and/or ratcheting wrench.

    If you have trouble turning the filter housing and your filter wrench is loose or slipping, try either wrapping the housing with some Gorilla Tape or insert a piece of newspaper or paper towel in to the wrench to give it some extra grip.

    Try to avoid rounding off the sides of the plastic filter housing, which may make it more difficult to remove during future oil changes.

    VW-Jetta-I5-Engine-Oil-Change-Filter-Replacement-Guide-019
    Replace Filter & O-Ring
    VW-Jetta-I5-Engine-Oil-Change-Filter-Replacement-Guide-020
    Replace Plastic End Cap
    VW-Jetta-I5-Engine-Oil-Change-Filter-Replacement-Guide-021
    Replace Engine Splash Shield
    Detach the filter wrench and continue spinning off the filter housing in the counter clockwise until it can be detached from the engine.

    Turn over the filter housing and drain out any remaining oil in to the used oil catch container.

    Pull out the old cartridge oil filter element and discard it. Use a pair of needle nose pliers or a small flathead screwdriver to remove the old rubber o-ring gasket at the bottom of the threads inside the filter cap.

    I recommend buying the Mann-Filter HU 719/6 Xoil filter since it has excellent reviews on Amazon.

    Lubricate the new o-ring with some new SAE 5W-40 motor oil and push it in to place at the bottom of the threads inside the oil filter housing. If the new o-ring is equipped with a small pull tab, position it in the up position for easy removal during the next oil change.

    Push the new cartridge oil filter down in to the housing until it clicks securely in to place.

    Clean up the area around the oil filter receptacle and make sure that the old rubber o-ring gasket or any part of it is not stuck to the engine.

    Spin on the oil filter housing in the clockwise direction to just past hand tight or about 25 Nm (18 ft-lbs) of torque.

    Do not over tighten the oil filter housing to avoid damaging the plastic housing, the threads or the rubber o-ring since it may cause an oil leak.

    Double check that the oil drain bolt and filter housing are tight before moving on the next steps.

    Line up the tabs on the front edge of the plastic engine underside cover and re-insert them in to the their corresponding slots by sliding the cover forwards.

    VW-Jetta-I5-Engine-Oil-Change-Filter-Replacement-Guide-022
    Replace Torx T25 Screws
    VW-Jetta-I5-Engine-Oil-Change-Filter-Replacement-Guide-023
    Turn Clockwise
    VW-Jetta-I5-Engine-Oil-Change-Filter-Replacement-Guide-024
    Tighten 8 Screws
    Replace the 8 screws and tighten them in the clockwise direction with the Torx T25 screwdriver until they are snug.VW-Jetta-I5-Engine-Oil-Change-Filter-Replacement-Guide-025
    Lower Car From Stands
    VW-Jetta-I5-Engine-Oil-Change-Filter-Replacement-Guide-026
    Insert Automotive Funnel
    VW-Jetta-I5-Engine-Oil-Change-Filter-Replacement-Guide-027
    Pour In New 5W-40 Oil
    Lower the car from the jack stands using the floor jack.

    Insert an automotive funnel in to the oil filler hole.

    Carefully pour in about 5.5 to 6 quarts of new SAE 5W-40 synthetic oil in to the engine.

    The 2.5L I5 engine's total capacity for an oil change with filter replacement is 6.3 U.S. qts (or 6.0 liters).

    It is far better to have slightly less oil than necessary in an engine than to have too much oil in it. Running an engine that has been overfilled with oil may damage seals, gaskets or other components.

    VW-Jetta-I5-Engine-Oil-Change-Filter-Replacement-Guide-028
    Replace Oil Filler Cap
    VW-Jetta-I5-Engine-Oil-Change-Filter-Replacement-Guide-029
    Check Dipstick Oil Level
    VW-Jetta-I5-Engine-Oil-Change-Filter-Replacement-Guide-030
    Engine Oil Change Complete!
    Replace the oil filler cap by twisting it on in the clockwise direction and push down the dipstick.

    Run the engine for a few minutes, shut it off, and allow the oil to drain back down to the pan for at least 5 minutes.

    Pull out the dipstick, wipe it clean, re-insert it, and pull it out again to check the oil level.

    If necessary, slowly pour in more oil while repeatedly checking the level on the dipstick until it reaches at or just below the "Full" line indicated by a metal dot at the top of the cross hatched area.

    You may not need to pour in the entire 6.3 quarts of new SAE 5W-40 oil depending on how long you allowed the old oil to drain out.

    To reset the oil change service reminder (indicated by a "wrench" image on the display), follow these steps: 1. Sit in the driver's seat, close the door, and turn off the ignition. 2. Press and hold the "0.0 / Set" trip meter button near the right side of the gauges and behind the steering wheel. 3. Turn the ignition to the "On" position but do not start the engine. 4. Release the "0.0 / Set" button. 4. Within 20 seconds, press the "minute" button on the left side of the dashboard just below the gauges and behind the steering wheel. The "wrench" symbol should now no longer be displayed.

    If your vehicle has the "Volkswagen Information System" multi function display screen in between the gauges, you'll need to turn the ignition switch to the "On" position but do not start the engine, navigate to the "Settings" menu, scroll down to "Service", push "OK", choose the "Reset" option and then select "OK" to reset the service interval.

    Be sure to record the oil change in your Jetta's service records.

    For more, check out my other VW Jetta DIY Repair Guides.
     

    Sours: https://paulstravelpictures.com/Volkswagen-Jetta-I5-Engine-Oil-Change-Guide/

    Filter volkswagen jetta location oil

    Yes, I'm not offended, I understand everything. You are what, if you need help with George, you say. I liked Georg, we must somehow add him to us. - Okay, I'll keep it in mind. Spring was coming.

    VW Jetta Oil and Filter (2011-2013)

    Well, nothing, if she still carries, then he knows how to arrange so that she lost her child. With these thoughts, Lyon sat down at the table and started writing a letter to his future father-in-law. She was one of my students.

    Similar news:

    And my car is broken today, I will have to walk home, which will take longer. So I'll leave - as soon as I can. - Everything will be all right, don't worry.



    2085 2086 2087 2088 2089